What is a good reusable bottle that isn't a mould farm?
-
I've had good luck with kleen kanteen. Stainless steel with a steel screw in top. No gaskets.
I know what you mean about the moldy gaskets, I've had that problem with insulated coffee mugs.
wrote last edited by [email protected]Use(d) their thermos for tea.
My smaller bottle had a big opening and easy to clean.
Sadly it went KIA during my commute and jumped out of my biking bag and onto the road.
On which it was later crushed by a car. It was a present
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
Using 2 bottles atm. Both from LTT (youtuber merch).
After use I clean them witg fresh water and dry them over night in a reverse position.
So far it was sufficient to not develop any smell. On ocassion I'll clean it with dish soap. -
Mold = dust/residues + dampness. Clean your bottles, and keep them dry when out of use - you can keep water filled bottles pretty long in the fridge.
My 4 year old bottles stay filled in the fridge; when a bottle travels with me, coming home i wash them with my bottle brush and a small amount of dish soap and either fill them right back up and put them in the fridge again, or i keep the cap off and let them dry thoroughly putting them upside down so droplets can get out. Anything else is just an invitation for mold.
wrote last edited by [email protected]At times I use boiling water plus dish soap after cleaning it with cold water.^(Obviously only with stainless steel and not plastic)
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
I just use a plastic volvic bottle. They're usually fine for a couple of weeks. I guess it would depend what's in your local water supply.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
I have about 10 protein/gym shakers, that I use for shakes (obviously) but also just water. I have so many because they will sometimes come free when i order supplements - but they can be bought for a few dollars. I rotate them daily and just run them through the dish washer. Because they're wide and the lid comes off they are super easy to wash and dry.
I'll normally get a couple years out of them before they need replacing.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
Yeti wide mouth because it's easy to clean. I just flush it with hot tap water and a drop of Dawn, let it sit for a few minutes, then hold my hand over the mouth and shake. Rinse thoroughly, then dry right side up so condensation doesn't build up inside. The part to really pay attention to is the mouthpiece, but that is quickly cleaned with some soapy water and a rag.
Also, DON'T use your dishes rag/sponge on your water bottles, as it always has residual dish gunk (no matter how many times you rinse it) that will actually make your water bottle dirtier. Keep a separate rag for washing drinking bottles and wring it properly when you're done.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
The solution to your problem is not to buy one specific bottle. The solution is to have two separate water bottles, so that you can swap and clean them on your own time.
-
Yeti wide mouth because it's easy to clean. I just flush it with hot tap water and a drop of Dawn, let it sit for a few minutes, then hold my hand over the mouth and shake. Rinse thoroughly, then dry right side up so condensation doesn't build up inside. The part to really pay attention to is the mouthpiece, but that is quickly cleaned with some soapy water and a rag.
Also, DON'T use your dishes rag/sponge on your water bottles, as it always has residual dish gunk (no matter how many times you rinse it) that will actually make your water bottle dirtier. Keep a separate rag for washing drinking bottles and wring it properly when you're done.
I have one of those and it’s the easiest bottle to clean that I have. Takes like 1 min from wet to totally dry. However, it’s not insulated so that may be an issue for them.
-
I have one of those and it’s the easiest bottle to clean that I have. Takes like 1 min from wet to totally dry. However, it’s not insulated so that may be an issue for them.
wrote last edited by [email protected]I saw an insulated one when i just checked. Price £40.
Edit: Here
-
I saw an insulated one when i just checked. Price £40.
Edit: Here
Oh nice, missed those.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
wrote last edited by [email protected]The Contigo Cortland chill.
I love this bottle so much if I lose it I buy another. I've been using this bottle for at least 6 years now.Because it's a button spout it's very good for air sipping (water falling). Since I don't put my mouth on it, there is less chance of bacteria developing in the bottle and lid.
The Lid folds open on the inside which makes it easy to clean by hand.
I see they have new filtered variants, I haven't tried those yet.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
Well I use a nalgene and a Kleen Kanteen. Both have that standard open mouth design. You're gonna need to clean the caps and O-rings but they're pretty good
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
Guaranteed to keep your water cool.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
wrote last edited by [email protected]
flip top stainless growler, get a bunch of extra gaskets and rotate them. I put them in the dishwasher in the cutlery tray that has a lid to keep things from flying out, then boil them submerged under a stainless trivet to get any smells out.
the bottles I just use soap and a brush and if it smells like anything after that then PBW or oxy powder.
bottles with straws, slide seals, the other type of flip lid, hollow lids, etc will inevitably have unwashable areas that will get nasty.
runner up is this. they fit the same opening
it looks like they dont sell the growler flip any more but I bought several for my klean kanteen knockoff (unintentional kkk) standard size bottles too.
-
The Contigo Cortland chill.
I love this bottle so much if I lose it I buy another. I've been using this bottle for at least 6 years now.Because it's a button spout it's very good for air sipping (water falling). Since I don't put my mouth on it, there is less chance of bacteria developing in the bottle and lid.
The Lid folds open on the inside which makes it easy to clean by hand.
I see they have new filtered variants, I haven't tried those yet.
I am the same with the steel version from them! I like that it’s made out of metal, but I do eventually fuck up the base because I drop it on the regular.
-
Kind of a rant — I drink water and flavored-water beverages, and I don't wanna buy 24-packs of water and trust my local municipality to recycle. Maybe they do, maybe they don't. Either way, it's not recycle, it's "reduce, reuse, recycle." I'll drink a Gatorade (Zero) and reuse it a few times and then toss it.
But if I want a reusable bottle — there's one by Aladdin (Thermos) I like, and one by Zojirushi, I've bought two of each over the years. Just tossed the Zojirushi. Zojirushi is a Japanese brand, very high quality, but a bit over-engineered. It's got this rubber gasket and plug that, you can clean them daily, they get black spots. Not sure if it's mould or what, but it's kinda gross and I don't like it. The Aladdin/Thermos one is a bit better, didn't think there was any mould anywhere until I dropped it, the cap flew out, mould farm inside! Nowhere that touched the beverage so that was nice. But I'm kinda done with both of them. I would rather just waste plastic than risk drinking from a mouldy reusable cup.
Are there reusable bottles that aren't mould farms?
wrote last edited by [email protected]get a non-plastic bottle. plastic is notorious for harboring bacteria, and mold, because they are prone to microscope crevices from forming. probably a metal one. you might want to use soap and hot water for metal containers.
-
I like wide mouth bottles that match the diameter of the rest of the bottle, because they are the easiest to clean. You can even just toss them in the dishwasher depending in the material.
I also try to only buy titanium bottles since they last a lot longer than stainless steel. Some brands are too expensive but ive gotten lucky in the past with no name brands.
i only use the metal ones that also hold hot liquids, much more convenient than just buying it for 1 temperature.
-
Yeti wide mouth because it's easy to clean. I just flush it with hot tap water and a drop of Dawn, let it sit for a few minutes, then hold my hand over the mouth and shake. Rinse thoroughly, then dry right side up so condensation doesn't build up inside. The part to really pay attention to is the mouthpiece, but that is quickly cleaned with some soapy water and a rag.
Also, DON'T use your dishes rag/sponge on your water bottles, as it always has residual dish gunk (no matter how many times you rinse it) that will actually make your water bottle dirtier. Keep a separate rag for washing drinking bottles and wring it properly when you're done.
a bottle brush is more appropiate.
-
Yeti wide mouth because it's easy to clean. I just flush it with hot tap water and a drop of Dawn, let it sit for a few minutes, then hold my hand over the mouth and shake. Rinse thoroughly, then dry right side up so condensation doesn't build up inside. The part to really pay attention to is the mouthpiece, but that is quickly cleaned with some soapy water and a rag.
Also, DON'T use your dishes rag/sponge on your water bottles, as it always has residual dish gunk (no matter how many times you rinse it) that will actually make your water bottle dirtier. Keep a separate rag for washing drinking bottles and wring it properly when you're done.
Yeti's are also one of the few that are dishwasher safe
That wide mouth is the real big money.
-
32oz wide mouth Nalgene for me. I have 3 and cycle them every 2 days. Dishwasher when I run it and bottle brush once a week. Never a hint of anything.
Watch out for those microplastics though
