I just fixed my joycon drift today!
-
You should have gone with Hall effect replacements since that’s a permanent fix. Not knocking on your effort, it’s a delicate work and you’ve got some practice in for the time you’ll have to go back to do that
Are there hall effects joysticks you can buy to replace them? Do you have any exaples of parts that you would recommend?
-
I installed one of those and had to RMA it within a couple weeks. Not saying don't "upgrade" but apparently there's no silver bullets here.
RMA due to drift? That’s rather unheard of, I’d be more inclined to suspect that you got a fake.
-
Are there hall effects joysticks you can buy to replace them? Do you have any exaples of parts that you would recommend?
I used GuliKit NS40 which is available on Amazon and other places. Get a kit with tools if you don’t have tri-wing screwdriver yet. I was replacing joysticks every couple of months until I got those but haven’t had to since then.
-
Recently bought a used Switch 1 as people were getting rid of them to buy the new one, but I found out that mine came with an insane amount of drifting.
Opening it up was a pain in the ass and pretty scary, but I managed to fix it by putting a card over the metal plate on the left (to apply pressure under the joystick as many people online instructed)... And it worked!
It used to drift all the way to the left whenever I let go of the analog stick, but now it snaps firmly back to the center. Just wanted to put out a PSA that if your Joycon is drifting, it's very fixable. All you need is the right screwdriver and being very careful when lifting up each piece.
I tried this but eventually it got drifty again. I then swapped the joysticks for the Gulikit hall effect sticks and resolved the issue permanently.
Also, I think the design of the joycon is good. It was much easier to repair than the gen1 quest controller. When I attempted to do the same shim fix I broke some ribbon cable clip rendering it unusable.
-
You should have gone with Hall effect replacements since that’s a permanent fix. Not knocking on your effort, it’s a delicate work and you’ve got some practice in for the time you’ll have to go back to do that
I think that TMR is now the preferred tech. It is more of a direct replacement than hall effect, resulting in less potential latency and maintaining the advantages of magnetic, contactless sticks.
-
I used GuliKit NS40 which is available on Amazon and other places. Get a kit with tools if you don’t have tri-wing screwdriver yet. I was replacing joysticks every couple of months until I got those but haven’t had to since then.
Excellent! I changed mine already with similar replacents and haven't had problems since, thankfully.
But if it happens again though, I'll know what to look for. Thank you!
-
I think that TMR is now the preferred tech. It is more of a direct replacement than hall effect, resulting in less potential latency and maintaining the advantages of magnetic, contactless sticks.
wrote on last edited by [email protected]I would probably find this out when Hall effect sticks died but they simply refuse to. Good to know though, thanks.
-
Recently bought a used Switch 1 as people were getting rid of them to buy the new one, but I found out that mine came with an insane amount of drifting.
Opening it up was a pain in the ass and pretty scary, but I managed to fix it by putting a card over the metal plate on the left (to apply pressure under the joystick as many people online instructed)... And it worked!
It used to drift all the way to the left whenever I let go of the analog stick, but now it snaps firmly back to the center. Just wanted to put out a PSA that if your Joycon is drifting, it's very fixable. All you need is the right screwdriver and being very careful when lifting up each piece.
I don't know. Spraying wd40 in (yes really) seems much easier and also easily redone when needed.
Also purchasing an 8bitdo ultimate.
-
RMA due to drift? That’s rather unheard of, I’d be more inclined to suspect that you got a fake.
Not drift. Replacement just stopped working. Double checked connections and even put back in the old joystick (in case a cable was damaged).
-
I genuinely have no idea. I've read online that it could be because of
- Skin oils
- Lotion
- Alcohol
- Other detergent
Skin oils seems ridiculous because I'm not oilier than your average person, and it's literally meant to be used with your fingers so if it can't handle skin oil from your fingers without breaking the fuck down that's a massive design flaw.
I basically just left it in its case for ~9 months or so, closed in the TV bench. There's no way UV reached it and broke down the plastic.
The fact that a ~€20 pack of 2 replacement switches are mechanically better, and also designed to have the caps be removable so you can replace them is criminal, given that the controllers themselves cost like €80 by default. I'm definitely not buying the Switch 2.
My previous mouse pad's rubber had been breaking down due to the oils and sweat and my palm pressure.
These things tend to do that.I have added this one additional consideration on frequently touched devices that I own.
Got a mouse, bought the plastic finish version instead of the rubber finish one.
Got headphones, considering (-ing because that was the thing that made me start considering and I didn't consider it before) ear-pad replacement options.
Got a torch with a rubber-like cover: well that's an outdoor thing made for light rain, so hoping it is rugged enough.
