I have dozens. I can't let go.
-
Stab yourself once while rummaging around and you never do that again. Stab yourself under the fingernail while rummaging around and you might burn a whole building down.
If you do any kind of precision work (e.g. electronics, glasses, changing the battery on a kid's toy, etc) I strongly encourage getting a proper precision driver and bit set. I like ifixit but there are knockoffs that come from literally the same factories for a lot cheaper. Those tend to come with a bit that is literally a sim ejector pin AND a box that keeps everything organized and together.
Put them in a box and put the box in the drawer.
-
Until you take out the most-common size, set it down somewhere, lose it, and have to buy another set, at which point you find the lost one.
Oh heavens! Can relate!
-
Put it, along with the documentation for whatever the thing is, and tape (packing tape works well) to the back of the thing. When it comes time to move or do something that requires the manual and/or tools, you have both the tools and documentation easily at hand and not lost in some junk drawer somewhere.
I like to put it all in a zipper sandwich bag together and tape that to the thing
-
This post did not contain any content.
They’re all the same, until they’re not. Some are extra long or specialized for the item being assembled. Sometimes they come with brothers.
I don’t know where they all go, but they’re here, somewhere.
-
This post did not contain any content.wrote last edited by [email protected]
They're the worst and I don't even use them the first time to assemble things in most cases, but I too have a whole bag of them.
-
This post did not contain any content.
After I started a 3d printing hobby all the hexes have been put to good use
-
They’re all the same, until they’re not. Some are extra long or specialized for the item being assembled. Sometimes they come with brothers.
I don’t know where they all go, but they’re here, somewhere.
I have a drawer specifically for things that tighten or loosen fasteners.
-
After I started a 3d printing hobby all the hexes have been put to good use
£10 says you have a set of flush cutters with blue rubberised handles.
-
£10 says you have a set of flush cutters with blue rubberised handles.
Wrong! I have 10 sets....
-
I'd love a picture so that I can speculate on options.
-
Torque wrenches take length into account in the calibration...
Well then I just suck at wrenching properly.
-
How many torques are on that?
Ideas:
- Weld a nut onto the top of it. Should be able to accomplish this with a MIG and a steady hand
- Cut a slot in the top with a rotary tool cutting wheel, use a large manual impact driver to crack it, or a dull chisel/flat punch and a hammer to tap it around (clearance might be an issue here)
- Rotary tool again, cut faces on two sides, locking pliers, turn them with channel locks
- Rotay tool yet again, cut faces on six sides, hammer a possibly sacrificial six point socket on it
-
£10 says you have a set of flush cutters with blue rubberised handles.
Mine broke, but.. guilty lol
-
How many torques are on that?
Ideas:
- Weld a nut onto the top of it. Should be able to accomplish this with a MIG and a steady hand
- Cut a slot in the top with a rotary tool cutting wheel, use a large manual impact driver to crack it, or a dull chisel/flat punch and a hammer to tap it around (clearance might be an issue here)
- Rotary tool again, cut faces on two sides, locking pliers, turn them with channel locks
- Rotay tool yet again, cut faces on six sides, hammer a possibly sacrificial six point socket on it
I like you, you're a good human. Saving this for if/when it needs to be replaced in the future.
-
This post did not contain any content.
i love my collection. no one will take my precioussss
-
This post did not contain any content.
Just purged about ten of these a couple of weeks ago.
-
This post did not contain any content.
if they could all be the same size as i need for my fruit boots (4mm i think) that would be perfect.
constantly losing those bastards.
-
This post did not contain any content.
I keep them all in the hope that some day I can have someone forge a lifetime of Allen wrenches into a Damascus steel battle-axe
-
I keep them all in the hope that some day I can have someone forge a lifetime of Allen wrenches into a Damascus steel battle-axe
I feel like there should be some quotes in there. Damascus "Steel"
-
I feel like there should be some quotes in there. Damascus "Steel"
For a minute I thought you were throwing shade at Damascus steel but then I realized that those Allen Wrenches are probably made of aluminum.
