Type of key? And how to get broken part out of lock?
-
Hot glue gun glue stick. Melt end, attach, wait a few, pull.
Yep. I’ve also used a paper clip, straightened out with a very small bend at the end.
I’ve also used chewing gum, though you have to wait it for it to harden a little. Duct tape might work too.
You only have to get it to move out a tiny amount. Then you can get a pair of needle nose pliers on it and pull it out.
That particular key looks challenging though.
-
This is the answer.
The only downside is you can see how stripped those screws are even in this photo. That'll be fun.
Yep. Use a rubber band in the screw when trying to unscrew it to help with a bit extra grip and then never use those screws again either. Either that or use a Dremel to turn it into a flat head screw and remove them.
-
Yep. I’ve also used a paper clip, straightened out with a very small bend at the end.
I’ve also used chewing gum, though you have to wait it for it to harden a little. Duct tape might work too.
You only have to get it to move out a tiny amount. Then you can get a pair of needle nose pliers on it and pull it out.
That particular key looks challenging though.
Tried a dab of super glue on a paper clip then held to the key?
-
I’m pretty strong for being a middle aged woman (so not strong in general), and I can break a key in a lock relatively easily with just my hands.
Uh... can I have your number?
-
Tried a dab of super glue on a paper clip then held to the key?
wrote on last edited by [email protected]Not likely enough surface area for cyanoacrylate to do its magic, though one could try to glue the key pieces together and hope it holds long enough for a partial pull. Likely to just glue the broken piece in there by accident.
Hot glue is gooey and will grab the broken part.
-
Not likely enough surface area for cyanoacrylate to do its magic, though one could try to glue the key pieces together and hope it holds long enough for a partial pull. Likely to just glue the broken piece in there by accident.
Hot glue is gooey and will grab the broken part.
I would have thought you'd struggle to get hot glue to bond sufficiently the metal or be able to get a small enough amount on a something thin enough quickly enough to get it to stick to the key end without getting all over the barrel.
-
1. Type of key?
The brand is Phillips but they make various types. The type here is (not sure of the correct jargon) without vertical ridges and notches. And both sides of the key are identical.
I've looked at some diagrams of key types and I'm not sure exactly. Is it a "dimple key"? Something else?
2. How to remove broken part from lock?
Location: Door between bedroom and garden.
Situation:
-
Someone bent the key a little, and it was stuck, couldn't get it out. On the inside of the door. At that point still able to lock and unlock from the inside only. Using other key from the outside does nothing, doesn't even turn.
-
I tried gently straightening it but it immediately snapped.
-
Now: can still open and close the door using the handle. Can still, with difficulty, lock and unlock the door (from inside only) by carefully pressing the head of the key against what is in the lock and turning.
A lot of info online for removing broken key blades from locks are for the "traditional" kind of key with vertical ridges and notches.
I have a screwdriver that fits all the screws and I can access all sides of the lock (inside, outside, edge), but I'm not sure if that's relevant. I've tried tweezers but it's too snug.
If I need more tools or equipment, I'll get them tomorrow.
Why wouldn't you just replace the whole lock?
-
-
Use a broken key extractor.
Wouldn't a functioning key extractor work better than a broken one?
-
1. Type of key?
The brand is Phillips but they make various types. The type here is (not sure of the correct jargon) without vertical ridges and notches. And both sides of the key are identical.
I've looked at some diagrams of key types and I'm not sure exactly. Is it a "dimple key"? Something else?
2. How to remove broken part from lock?
Location: Door between bedroom and garden.
Situation:
-
Someone bent the key a little, and it was stuck, couldn't get it out. On the inside of the door. At that point still able to lock and unlock from the inside only. Using other key from the outside does nothing, doesn't even turn.
-
I tried gently straightening it but it immediately snapped.
-
Now: can still open and close the door using the handle. Can still, with difficulty, lock and unlock the door (from inside only) by carefully pressing the head of the key against what is in the lock and turning.
A lot of info online for removing broken key blades from locks are for the "traditional" kind of key with vertical ridges and notches.
I have a screwdriver that fits all the screws and I can access all sides of the lock (inside, outside, edge), but I'm not sure if that's relevant. I've tried tweezers but it's too snug.
If I need more tools or equipment, I'll get them tomorrow.
superglue.
-
-
Why wouldn't you just replace the whole lock?
wrote on last edited by [email protected]This. Some people don't realise how ridiculously easy it is to change a lock when you can open the door with a key.
-
Put the working key into the lock
-
Undo this screw
-
Turn the key slightly back and forth whilst pulling the cylinder out until it starts to come out. Then just pull it all out.
-
Mark which side was front and back
-
Measure from the middle locking mechanism of the cylinder to the ends.
-
Find a lock with the same lengths. It'll be like 60/40 (100mm total length).
6b. Optional: get one with a fixed turnkey on the inside.
- Replace lock by reverse.
-
-
Wouldn't a functioning key extractor work better than a broken one?
I like the cut of your jib.
-
Dental pick, like the kind that your hygienist uses to give you PTSD should do the trick.
OP’s description of trying to pull the key out when it broke, makes me think the key may also be bound/frozen in the lock. I don’t think you’re supposed to use wet lubricants in a lock, but they may need to use a penetrating lubricant (like wd-40) along with the dental pick.
-
This is the answer.
The only downside is you can see how stripped those screws are even in this photo. That'll be fun.
wrote on last edited by [email protected]On this type of latch (mortise) the third screw is often stripped (because it’s a set screw that holds the lock cylinder in place and often the notch in the cylinder is misaligned / on the wrong side) but _un_screwing it should be easy.
The cylinder itself, however, is usually finely threaded and can require a fair amount of torque to get started, especially without using the key for additional purchase.
-
1. Type of key?
The brand is Phillips but they make various types. The type here is (not sure of the correct jargon) without vertical ridges and notches. And both sides of the key are identical.
I've looked at some diagrams of key types and I'm not sure exactly. Is it a "dimple key"? Something else?
2. How to remove broken part from lock?
Location: Door between bedroom and garden.
Situation:
-
Someone bent the key a little, and it was stuck, couldn't get it out. On the inside of the door. At that point still able to lock and unlock from the inside only. Using other key from the outside does nothing, doesn't even turn.
-
I tried gently straightening it but it immediately snapped.
-
Now: can still open and close the door using the handle. Can still, with difficulty, lock and unlock the door (from inside only) by carefully pressing the head of the key against what is in the lock and turning.
A lot of info online for removing broken key blades from locks are for the "traditional" kind of key with vertical ridges and notches.
I have a screwdriver that fits all the screws and I can access all sides of the lock (inside, outside, edge), but I'm not sure if that's relevant. I've tried tweezers but it's too snug.
If I need more tools or equipment, I'll get them tomorrow.
There's a pretty good chance that you can get a bit of wire or a fine pick and push the key through from the other side, I'd be trying that first.
Aside from that the next easiest solution is likely to just disassemble the lock and replace the cylinder as others have suggested.
-
-
1. Type of key?
The brand is Phillips but they make various types. The type here is (not sure of the correct jargon) without vertical ridges and notches. And both sides of the key are identical.
I've looked at some diagrams of key types and I'm not sure exactly. Is it a "dimple key"? Something else?
2. How to remove broken part from lock?
Location: Door between bedroom and garden.
Situation:
-
Someone bent the key a little, and it was stuck, couldn't get it out. On the inside of the door. At that point still able to lock and unlock from the inside only. Using other key from the outside does nothing, doesn't even turn.
-
I tried gently straightening it but it immediately snapped.
-
Now: can still open and close the door using the handle. Can still, with difficulty, lock and unlock the door (from inside only) by carefully pressing the head of the key against what is in the lock and turning.
A lot of info online for removing broken key blades from locks are for the "traditional" kind of key with vertical ridges and notches.
I have a screwdriver that fits all the screws and I can access all sides of the lock (inside, outside, edge), but I'm not sure if that's relevant. I've tried tweezers but it's too snug.
If I need more tools or equipment, I'll get them tomorrow.
Strong magnet maybe?
-
-
Strong magnet maybe?
thanks david
-
Neat! Didn't know there was such a thing. Another poster suggested a dental pick kit, not as good but more versatile.
You can dental pick a lock, but can you lock pick a dentist?
-
1. Type of key?
The brand is Phillips but they make various types. The type here is (not sure of the correct jargon) without vertical ridges and notches. And both sides of the key are identical.
I've looked at some diagrams of key types and I'm not sure exactly. Is it a "dimple key"? Something else?
2. How to remove broken part from lock?
Location: Door between bedroom and garden.
Situation:
-
Someone bent the key a little, and it was stuck, couldn't get it out. On the inside of the door. At that point still able to lock and unlock from the inside only. Using other key from the outside does nothing, doesn't even turn.
-
I tried gently straightening it but it immediately snapped.
-
Now: can still open and close the door using the handle. Can still, with difficulty, lock and unlock the door (from inside only) by carefully pressing the head of the key against what is in the lock and turning.
A lot of info online for removing broken key blades from locks are for the "traditional" kind of key with vertical ridges and notches.
I have a screwdriver that fits all the screws and I can access all sides of the lock (inside, outside, edge), but I'm not sure if that's relevant. I've tried tweezers but it's too snug.
If I need more tools or equipment, I'll get them tomorrow.
While an ignorant rober is trying his luck at trying to open your door a smart one is already gone with your stuff and the police already blasted your door open. I would just get a normal key.
-
-
Hot glue gun glue stick. Melt end, attach, wait a few, pull.
I saw this on TikTok once /jk
-
Hot glue gun glue stick. Melt end, attach, wait a few, pull.
Very small, precision needle-nose pliers work as well, but there needs to at least be a very small part of the key-break to grab. If the key somehow snaps in a position that's even slightly recessed, I've used a tootpick and tiny dab of superglue (not enough to spread and touch the lock itself - be careful lol).
