I derusted a vise left by the previous tenant of the house
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
-
System shared this topic on
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
TIL that you could spell vice, vise as well!
-
TIL that you could spell vice, vise as well!
I did not want anyone to think I was derusting my personal failings.
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
For future reference, Eastwood make a rust removal gel that you can paint onto surfaces and does a pretty great job. There's also naval jelly which is a generic phosphoric acid solution that can also be painted on and washed off.
-
I did not want anyone to think I was derusting my personal failings.
In UK English we spell it vice for a "mechanical object used to secure things". I had never seen it spelt "vise".
-
In UK English we spell it vice for a "mechanical object used to secure things". I had never seen it spelt "vise".
Not native English speaker, so I checked the dictionary first, and saw that vise is an accepted alternative spelling. Might not be that common apparently.
-
For future reference, Eastwood make a rust removal gel that you can paint onto surfaces and does a pretty great job. There's also naval jelly which is a generic phosphoric acid solution that can also be painted on and washed off.
I checked the biggest retailers in my neck of the woods, doesn't look like any of them sell it.
-
Not native English speaker, so I checked the dictionary first, and saw that vise is an accepted alternative spelling. Might not be that common apparently.
It is more just the difference between UK English and US English, nothing wrong with using either of them this is just one of those things that I wasn't aware had a different spelling until today.
It is like tyres - UK or tires - US. Tires looks wrong to me because I grew up using tyres but they are both valid spellings of the word.
-
I checked the biggest retailers in my neck of the woods, doesn't look like any of them sell it.
You might find naval jelly at a marine supply store, I think Permatex makes a version. The Eastwood stuff might have to be purchased at an commercial auto paint store.
-
It is more just the difference between UK English and US English, nothing wrong with using either of them this is just one of those things that I wasn't aware had a different spelling until today.
It is like tyres - UK or tires - US. Tires looks wrong to me because I grew up using tyres but they are both valid spellings of the word.
Hmm, looks like it's the US spelling for a gripping tool, whereas UK uses vice for both a personal failing or a bad habit, and a gripping tool. I'm most familiar with US spelling since I learned most of my English from video games and TV shows as wee lad.
-
You might find naval jelly at a marine supply store, I think Permatex makes a version. The Eastwood stuff might have to be purchased at an commercial auto paint store.
After some research, apparently my local auto store does sell a store brand rust removal gel. As a bonus, in my local language it's apparently called "Rust eater".
-
After some research, apparently my local auto store does sell a store brand rust removal gel. As a bonus, in my local language it's apparently called "Rust eater".
Cool. Keep in mind, this is @ 20% phosphoric acid and sometimes a bit of hydrochloric as well, you don't want to get it on paint or concrete. But it works a treat, if it's thin enough you can get it into a spray bottle or water it down a bit if you need.
-
Cool. Keep in mind, this is @ 20% phosphoric acid and sometimes a bit of hydrochloric as well, you don't want to get it on paint or concrete. But it works a treat, if it's thin enough you can get it into a spray bottle or water it down a bit if you need.
I will keep this advice in mind the next time I need to derust something. Thank you very much. Bought a house from the 80's from a family of the previous owner, and they left a whole bunch of potentially good tools and other stuff in there.
A badly maintained, clogged, greasy electric chainsaw is on my list of things to open up, clean and lube up as well. Looking forward to that, as a mainly electronics guy, I only very recently started doing mechanical engineering. Opened up a fan that had a hard time turning, found out there were no bearings, just a rod acting as the iron core inside a DC motor. Disassembled, applied generous amounts of acetone to relevant parts, dried it up and greased it up. Worked like a charm afterwards, and didn't even lose any screws.
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
Your mistake was buying derusting solution. Just use vinegar with some salt.
.... Unless that was your derusting solution, then your mistake was not buying more vinegar.
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
You should definitely paint all the surfaces that aren't machined, as that's very likely how it would have been originally.
Also, what's dull about restoring a tool? There are entire YouTube channels devoted to it that are pretty darn popular. (Or so I'm told, as I would surely not watch something so dull myself. <AwkwardLookMonkeyPuppet.jpg>)
-
You should definitely paint all the surfaces that aren't machined, as that's very likely how it would have been originally.
Also, what's dull about restoring a tool? There are entire YouTube channels devoted to it that are pretty darn popular. (Or so I'm told, as I would surely not watch something so dull myself. <AwkwardLookMonkeyPuppet.jpg>)
I am sincerely apologetic of posting content that you found not to be dull enough. I will try to be better in the future. Tool restoration indeed is interesting, but I thought merely soaking a tool in deruster for days would be dull enough
-
It is more just the difference between UK English and US English, nothing wrong with using either of them this is just one of those things that I wasn't aware had a different spelling until today.
It is like tyres - UK or tires - US. Tires looks wrong to me because I grew up using tyres but they are both valid spellings of the word.
I suspect we can thank Daniel Webster for trying to simplify spellings. I'm still not sure how I feel about it - I find some words make better sense spelled in the British way, like "behaviour", but I also appreciate the vice homonym spellings.
At least the [vice](vice Etymology of vice by etymonline
https://www.etymonline.com/word/vice#7762) / vise spellings make sense etymologically - they have separate Latin origins (see links). I can't explain why British English doesn't make this distinction, especially since they were different in Old French and Anglo-French. -
Your mistake was buying derusting solution. Just use vinegar with some salt.
.... Unless that was your derusting solution, then your mistake was not buying more vinegar.
I've been using vinegar for this for most of my life but have never added salt. Does that speed it up, or help in some other way?
-
I've been using vinegar for this for most of my life but have never added salt. Does that speed it up, or help in some other way?
I don't actually know if it helps at all. Vinegar on its own also seems to work.
-
I had no free buckets to hold the derusting solution in that the vise would fit comfortably, so I had to use a plastic box that was too wide. It would not submerge fully in the 1 Liter of derusting solution I bought, I had to soak one side for 24 hours and then the other side for 24 hours. It mostly cleared the rust. I'm considering painting it now, but I don't think I'm going to.
Probably want to oil it so it doesn't get rusty again.
